What a cake stand is

A cake stand is a plate raised on a foot or a stem. The French call it a présentoir à gâteaux or a plat à gâteau sur pied; the footed dish of a dessert service is a compotier. A cake plate is the same idea without the height: flat, or on a very low foot. Most stands on the market date from about 1870 to 1960.

MaterialWhat you findLook at first
Pressed glassAmerican patterns such as Daisy and Button, Bull’s Eye and Westward HoMold seams, chips on the rim and the foot
Barbotine (majolica)Leaves and fruit, from Onnaing, Saint-Clément and SarregueminesGlaze loss and hairlines
PorcelainLimoges and Paris compotiers from dessert servicesFactory mark, gilding wear
SilverplateChristofle and other makersPlating wear, the joint at the stem
Glass of the 1920s and 1930sArt Deco standsChips, the stem join

Our encyclopedia entry on the cake stand gives indicative price ranges.

The forms

  • Pedestal stand. A plate on a stem, made in one piece or in two parts joined at the stem.
  • Footed cake plate. Lower and more stable, easier to store.
  • Compotier. The footed dish of a porcelain dessert service; worth more with the rest of the set.
  • Tiered stand. Two or three plates on a central rod. Many are later assemblies made from drilled plates, which a seller should say.
  • Stand with a dome. A glass cloche over the plate, also used for cheese; see French cheese serveware.

What size to buy

Choose a plate at least 1–2 in / 3–5 cm wider than the cake. A stand 10–12 in / 25–30 cm across takes a round cake of 8–9 in / 20–23 cm. Measure the flat area, not the rim: a molded or raised rim reduces the usable surface.

For a dome, measure the inside diameter and the height. On the table, check the height too. A tall stand can block the view across a narrow table.

What to check

  1. Rim and foot. They take the knocks. Run a fingernail around both for chips and ground-down repairs.
  2. The stem join. On a two-part stand, look for glue, cracks or a lean where plate and stem meet.
  3. Stability. Set it on a flat surface and press the edge. It should not rock.
  4. Pressed glass. Faint mold seams are normal and are not damage. Pressed glass pitchers explains how to read them.
  5. Barbotine and faience. Look for glaze loss and hairlines; see antique majolica plates.
  6. Porcelain. Look for the factory mark and wear on the gilding.
  7. Tiered stands. Ask for a photograph of each plate, the center hole, the washers and the rod. A leaning rod or a chipped hole matters.
  8. Dome. It should sit inside the rim without rocking.

Serving food on an old stand

Pressed glass and plain porcelain in sound condition are the simplest choice for serving. Put the cake on a board first: it protects the surface from the knife.

Old glazed earthenware needs more care. The FDA advises caution with glazed pottery that is antique, worn or of unknown manufacture, because some glazes contain lead. Keep a barbotine stand for display, or for wrapped and non-food items, unless you know it is safe. Do not cut on worn gilding or painted decoration.

Lead crystal is a separate case, covered in vintage crystal glassware: safe use.

Care and display

Wash by hand in warm water and dry at once. Avoid the dishwasher and sudden changes of temperature. Store plates and stems apart, each padded.

A cake stand earns its place between parties: it holds fruit on a kitchen counter, cheese under a cloche, or small pots on a dresser. Stack two of different sizes for a tiered display. For the rest of the table, see French country tableware and antique French glass.

Frequently asked questions

What is the difference between a cake stand and a cake plate?

A cake stand is raised on a foot or a stem, so the cake sits above the table. A cake plate is flat or stands on a very low foot. The stand shows the cake better; the plate is more stable, easier to carry and easier to store. A compotier is the footed dish of a dessert service.

What size cake stand do I need for a 9-inch cake?

Choose a stand at least 1 to 2 in (3 to 5 cm) wider than the cake, so 10 to 12 in (25 to 30 cm) for a 9-inch cake. Measure the flat part of the plate rather than the outer rim, because a molded or raised rim reduces the usable surface.

How can I tell if a glass cake stand is pressed glass?

Pressed glass is made in a mold, so it shows two to four faint vertical seams, rounded pattern edges and thick walls. Cut crystal is heavier, rings when tapped and has sharp edges under a fingernail. A pattern name identifies a design, not a year, because molds were reused for decades.

Are tiered cake stands original?

Not always. Many tiered stands are later assemblies made by drilling ordinary plates and joining them with a rod and washers. That is acceptable when the seller says so. Ask whether the holes were drilled later and whether the fittings are original, and check each center hole for chips.

Can I serve food on a vintage cake stand?

Pressed glass and plain porcelain in sound condition are the usual choice, with the cake on a board. For old glazed earthenware such as barbotine, the FDA advises caution with pottery that is antique, worn or of unknown manufacture. Keep such a stand for display unless you know it is safe.

Sources & further reading

Makers and dates are those given in our encyclopedia entry. The food-contact note is general guidance, not a test of any object.